Lingenfelter NCC-003 multi-stage Progressive Nitrous Controller

$599.95

Model: L460360003 Manufacturers: Lingenfelter Engineering

Qty:

Add to Wish List

Description

Lingenfelter NCC-003 multi-stage Progressive Nitrous Controller

The Lingenfelter NCC-003 is a multi-stage progressive nitrous controller that provides two stages of fully independent, progressive fuel and nitrous control. Nitrous can be activated or disabled based on a variety of inputs and safety over-rides. The controller also provides outputs to control relays and other devices based on almost any combination of all of the inputs along with shift light and timer outputs.
The NCC-003 nitrous controller is based on the same components used in the Lingenfelter NCC-002 nitrous control center except it does not have an onboard display or keypad, reducing the cost of the controller. Like the NCC-002, the NCC-003 has built in data logging designed to provide vital information during testing and competition.
Part Number: L460360003
Retail: $599.95
NCC-003 Features:
- Time based safety over-ride
- Time based nitrous control
- RPM based nitrous enable
- MPH based nitrous enable
- Gear position based nitrous enable
- Independent Stage 1 and Stage 2 delay adjustments
- User configurable between Hold & Wait or full reset when activation is removed and re-enabled. Hold & Wait resumes the progressive system at the point where the system was disabled (for example, where the throttle was released)
- Independent Stage 1 and Stage 2 nitrous and fuel resume ramp rates
- Independent Stage 1 and Stage 2 fuel advance settings
- These settings allow you to fine tune the system so that the low pressure fuel is delivered to the engine at the same time or before the high pressure nitrous, helping reduce the chances of initial lean spikes when each stage of nitrous is activated
- Multiple solenoid frequency settings independent for Stage 1 & 2
- Data logging built in you will need a PC or laptop to read and view data
- All channels logged at 100 samples second with a 25 second logging time
- Nitrous user settings stored in each data log for ease of recalling past nitrous settings
NCC-003 inputs and outputs:
- Independent control of both nitrous and fuel duty cycle for each stage
- Four stages of nitrous if used to only control nitrous solenoids
- Timer/RPM based output (+12V)
- Relay output (+12V) - programmable based on any combination of: Arming input, clutch input, shift input, TPS %, AFR, Nitrous1 %, Fuel1 %, Nitrous2 %, Fuel2 %, RPM, MPH, Fuel PSI, and Nitrous PSI
- Relay output (Ground) - programmable based on any combination of: Arming input, clutch input, shift input, TPS %, AFR, Nitrous1 %, Fuel1 %, Nitrous2 %, Fuel2 %, RPM, MPH, Fuel PSI, and Nitrous PSI
- Shift light output +12 volt
- Analog voltage output, programmable - for sending to a data acquisition system or to an ECM for external fuel or spark control
- Can link to the LNC-2000 or LNC-2001 for progressive timing retard on GM LSx V8 engine vehicles
- Arming input Ground or +12 volt selectable
- Clutch input - for clutch switch, line-lock, or trans-brake input Ground or +12 volt selectable
- Shift input - for gear position Ground or +12 volt selectable
- Nitrous bottle pressure input, 0-5 volt
- Fuel pressure input, 0-5 volt
- AFR input, 0-5 volt
- TPS input - accepts rising and falling voltage signal sensors, 0-5 volt
- Two analog inputs - accepts rising and falling voltage clutch position sensors, 0-5 volt
- Frequency input
- For vehicle speed
- Can connect to many OEM ECM VSS output signals or to a driveshaft speed sensor
- Software enable/disable pull-up resistor on frequency input
- Engine speed input tach
- Software enable/disable pull-up resistor on tachometer input
- Accepts most engine configurations
Benefits:
- AFR and fuel pressure safety shut-off
- Closed loop bottle heater control using relay output and nitrous pressure input
- Programmable via PC or laptop
- Free software updates PC or laptop plus internet access required
- Performs the same functions as several devices combined
Specifications:
- Billet CNC machined black hard coat anodized aluminum case with stainless backing plate
- Fully potted circuitry for increased durability in harsh racing environments
- PC programmable USB interface software
- Windows XP, Vista, 7 and 8 compatible
- Also Windows 8 tablet compatible
Additional components can be purchased separately:
- NCC labeled wiring harness PN: L480310000
- Fuel pressure sensor harness PN: L480290000
- Nitrous pressure sensor harness PN: L480300000
- Fuel pressure sensor, 0-15 psi PN: L480250015
- Fuel pressure sensor, 0-150 psi PN: L480260150
- Nitrous pressure sensor, 0-2000 psi PN: L480272000

This product was added to our catalog on Wednesday 18 November, 2015.

Points & Rewards Information

Points Credit : 600 points Currently valued at $18.00 Write a Review and earn $1.5 worth of points. Please check the Reward Point Program FAQ for more information.

Product 113 of 3870 in category Nitrous Systems Corvette

Lingenfelter NCC-003 multi-stage Progressive Nitrous Controller

Home

Specials

My Account

Call Us: